Aeroplane home-building: List of picture pages

Navigation & Acknowledgements

35mm film can spray gun	3D Mouldings label in bonding area	Access hole in cockpit module tunnel
Adjusting height of wing sling	Aileron drive bolt alignment	Aligning flap hinge plates FL1 FL2 FL3
Arbour press ram modification	Bad and good airline connectors	Beam balance fine adjuster
Bonding clip for sight gauge tubing	Bonding CS02 and CS03	Bonding CS05 to CS03
Bonding in port wing horn boxes	Bonding pitot/static tubing clips	Boring crank arm hole
Both wings in garage	Brake filler hole cover	Bridge to hold down tubing clips
BT Research Labs Martlesham Heath	Checking CS05 centre distance	Cockpit module pre-bond inspection rig
Cockpit module spar bush bonding	Cockpit module trimmed and fretted	Conduit sleeves and tube clips
Crank arm clamped to CS03 for drilling	CS04 clamped in position	CS04 shaped to fit
CS10 pivot markings	CS14 alignment	Cupboards for glass and resin
Cutting away TE between aileron and flap	Dispenser bottle nozzles	Double marking of holes in cockpit module
Double tube clip material	Dowel roller for inside wing repair	Drilling pushrod ends using vee-blocks
Drilling the torque tube hole in the seat face	Dummy pitot-static mast	Enlarged gate for trailer
Enlarging aileron hinge screw holes	Filing CS09A	Filing down CS07/CS08
Finger strainers and tank adaptors	Finishing rudder port side	Finishing rudder tip
Fitting fuel valve mounting plate	Fitting trailer floor	Flap
Flap attachment bolt almost threadbound	Flap hinge clamp	Flap hinge plate alignment tools
Flap hinge plates FL1 FL2 FL3	Fuel gauge sender head	Fuel pipes from tank to selector valve
Fuel tank adaptors	Fuel valve trial assembly	Fuselage dolly
Fuselage trim line	Garden shed	Gel coat drips & runs
Gel-coat trial finish	Gel-coating rudder	GPO Research Station Dollis Hill
Holder for thinning FL11	Holes in the wing skin	Horn-box recess enlarged
Instrument sub-panel	Ipswich airport	Kit parts
Landing gear mount corrosion	Lumps on wing top skin	Making clips for stall-warner tube
Making fuel tank adaptors	Making support sleeves for wing conduit	Making wooden handle for brake lever
Marking out for fuel gauge sender	Model aeroplanes	Modified iron
New peel-ply roll mount	One-cup resin balance	Outrigger
Parts spread out on lawn	Pitot-static mast connexion	Pitot-static tubing connectors
Plastic bottles	Port aileron bellcrank mount	Port flap aligned with aileron
Port flap clamped to template	Port tip flange misalignment	Port wing aileron bellcrank
Port wing aileron closeout cutaway	Port wing on flap template	Port wing skin pre-bonding
Port wing skin slotted to clear tip flange misalignment	Port wing tilted onto LE	Positioning CS09
Potential control restriction	Preparing for spar bush bonding	Radio and intercom
Re-bonding port wing TE	Redux pre-bond thickness on port wing ribs	Redux spread ready for wing skin bond
Redux surplus after pre-bonding	Redux test piece	Redux test piece broken
Redux thickness on starboard rib flanges	Release film for wing skin pre-bonding	Resin pump calibration checks
Right-angle adaptor for wing-leveller servo	Routing out brown foam	Rowland with hammer
Rudder flange damage	Rudder jig for sanding	Rudder layup
Rudder port side filled	Rudder starboard side polished	Sagging filler
Sander for curved parts	Sanding filler on rudder	Sandvik abrader
Screw spacers for stiffnuts	Servo mount bolts safetied	Setup for first aileron hinge hole
Spar - bellcrank clearance	Spraying CS05 torque tubes	Starboard wing conduit tryout
Starboard wing on car roof bars	Tailplane alignment	Tailplane outboard rib
Tailplane pip pin recesses	Tailplane tips	Tank spacer layup
Tank support layups	TE support for sanding	Thin patches on rudder root
Thin spots on rudder hinge vee	Tools	Trailer ramp gas springs
Trial hole for transponder head	Trim and anti-servo tab	Tubing clip bond failure
Unidentified objects in fuel tank	Void between rib and bottom skin	Weekend Workshop
Weights for wing skin bonding	Wet sanding with guide coat	Wing conduit installation
Wing leveller servo mounted	Wing rear closeout spacer	Wing repair completed
Wing skin bonded	Wing skin cut away for repair	Wing slings
Wing TE aileron closeout trimming	Wing tip support	Wings first pinned together
Wooden block for rudder hinge vee

Return to Rowland's home page	go to list of text pages	go to list of milestones
		go to building hours graph

This page last updated 2009-11-07. I try to make this page as accessible as possible, by adhering to HTML 4 standards.
I welcome comments on this website. However, because of the amount of spam it attracts, I no longer post a direct e-mail address on this page. Instead, please click here to contact me using my i-name =Rowland.Carson. You will have to confirm that the message is genuine before it will be sent on to me.